Arduino by Davis: “Adafruit’s Pi T-Cobbler #piday #raspberrypi @Raspberry_Pi” plus 19 more

---

• Adafruit’s Pi T-Cobbler #piday #raspberrypi @Raspberry_Pi
• Re: [OT ITA] Lo spamm bar
• Re: combine elements from two sketches
• Re: [Einsteiger] Nur von Luft und Liebe.. äh Licht
• Re: Infrared Reflectance Sensor
• Re: Problème avec un BMP05 et un arduino UNO ethernet
• How to program 16-bit pwms in the different Arduino boards ?
• Re: Tansistor help to power motors
• Re: firmata + vb.net
• Re: Componente per riscaldare acqua
• Re: Überlaufprobleme umgehen
• Inside-out Eggbot #piday #raspberrypi @Raspberry_Pi
• Re: Windows 7 and driver signing
• Re: 3 axis accelerometer to monitor dryer.
• Re: Weather sealing a PIR motion sensor ideas?
• Re: [Einsteiger] Nur von Luft und Liebe.. äh Licht
• how to use LabVIEW for receive data from serial monitor ?
• MOVED: Program the Arduino Ethernet board
• Re: Überlaufprobleme umgehen
• Re: Controlling and powering a heating element, thermometer, and screen.

Adafruit’s Pi T-Cobbler #piday #raspberrypi @Raspberry_Pi Posted: 11 Jan 2013 02:00 AM PST Here's a great post about the Adafruit Pi T-Cobbler from Meltwater's Raspberry Pi Hardware: The Pi T-Cobbler is supplied in 4 parts (plus a ribbon cable to connect it to the Raspberry Pi) which require soldering together; the PCB, the 26 pin IDC header and two 13 pin connectors . Soldering the item is quite simple. Fit the pin headers first, so that you can hold them flat on the desk while you solder. It is helpful to solder one pin on each end and then check that everything is flat, level and nicely aligned). Check carefully for any joints which have too little solder, or any which may have too much joining pins together. There are lots of pins to solder, but it is great soldering practise since it is only plastic which will melt if you over heat it (rather than the risk of damaging components).  Just take a little bit of care since it can be a little small and fiddly to hold, and the pins will stay hot. Read more. Featured Adafruit Products! Adafruit Pi T-Cobbler Breakout Kit for Raspberry Pi: Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi T-Cobbler from Adafruit, which can break out all those tasty power, GPIO, I2C and SPI pins from the 26 pin header onto a solderless breadboard. This mini kit will make "cobbling together" prototypes with the Pi super easy. Designed for Raspberry Pi Model B Revision 1 or Revision 2. (read more) Each Friday is PiDay here at Adafruit, be sure to check out our posts, tutorials and new Raspberry Pi related products. Have you tried the new "Adafruit Raspberry Pi Educational Linux Distro" ? It's our tweaked distribution for teaching electronics using the Raspberry Pi. But wait, there's more! Try our new Raspberry Pi WebIDE! The easiest way to learn programming on a Raspberry Pi. Want a FREE RASPBERRY PI? All orders over $350 get a FREE Raspberry Pi Model B with 512MB RAM!

Re: [OT ITA] Lo spamm bar Posted: 11 Jan 2013 01:56 AM PST su windows ci sono un'infinità di ambienti, quasi tutti a pagamento... astro aveva detto il suo preferito, ma non ricordo il nome, guarda qualche pagina indietro. Sul sito STM trovi il link alle librerie ufficiali con degli esempi con tanto di progetti...

Re: combine elements from two sketches Posted: 11 Jan 2013 01:56 AM PST You have started to tidy up the code as well as using the encoder to fool the program into thinking that buttons have been pressed which has confused things somewhat. In post 5 I suggested setting the value of LastButtonPushed to buttonPinRight or butt...

Re: [Einsteiger] Nur von Luft und Liebe.. äh Licht Posted: 11 Jan 2013 01:55 AM PST Hallo, @blubb113 Ich finde Dein Projekt ja super interessant, sei´s vom technischen, als auch vom softwaremäßigen Standpunkt aus. Aber das ist auch mit einigem Aufwand verbunden! Quote doch ich hab kein Bock auf Led an, led aus Bist Du Dir sic...

Re: Infrared Reflectance Sensor Posted: 11 Jan 2013 01:51 AM PST Reflectance sensors are finicky things. Try to bend the LEDs / phototransistors a bit so they point towards each other (imagine the light bouncing off the surface between the LED / phototransistor). Play around with the distance to your target and what...

Re: Problème avec un BMP05 et un arduino UNO ethernet Posted: 11 Jan 2013 01:50 AM PST Hello skywood, alors il y a tout un tas de trucs que je ne connais pas, et surtout c'est que le modèle que j'ai ne correspond pas tout a fait avec le descriptif. j'ai mis en pièce jointe la photo du produit et celle qui était dans le zip. Tu as sureme...

How to program 16-bit pwms in the different Arduino boards ? Posted: 11 Jan 2013 01:28 AM PST Hello, I currently have an Arduino Mega board and one of my needs is to produce PWM signal at high frequency (for example 30khz), and if possible with 12bits or 16bits resolution. I also plan to buy an Arduino Due to be able to do this and to have mor...

Re: Tansistor help to power motors Posted: 11 Jan 2013 01:26 AM PST i have been thinking about it whats the point of having 4 transistors in an H-Bridge? i mean, wont i be able to reverse, foward and stop a motor using just two transistors?

Re: firmata + vb.net Posted: 11 Jan 2013 01:26 AM PST L' unterfacciamento col sensore é diverso ma una volta che hai letto il valore il resto é uguale. Ciao Uwe

Re: Componente per riscaldare acqua Posted: 11 Jan 2013 01:24 AM PST Quote from: davide90 on January 10, 2013, 07:38:04 PM Scusa cosa vuoi dire con "come parli" ? mi sembra che questo sia un forum e sia fatto per chiedere a chi ne sa più di me in questo campo, non mi sembra che sto chiedendo mi...

Re: Überlaufprobleme umgehen Posted: 11 Jan 2013 01:22 AM PST Quote from: Chris72622 on Today at 04:15:16 AM Sorry. Es geht mir um den zeitlichen Überlauf. Meinst Du damit das der millis() Zähler nach 59 Tagen überläuft? Das ist unkritisch, wenn man "richtig" herum rech...

Inside-out Eggbot #piday #raspberrypi @Raspberry_Pi Posted: 11 Jan 2013 01:00 AM PST Cool project shared on the Evil Mad Science blog: Here's something we never thought of: John Fisher is using an EiBotBoard (EBB), a Raspberry PI and a camera to create "inverse panorama views" of cylindrical objects. It's a little bit like using an Eggbot as a scanner. His in-depth article covers everything from hardware set up to code. Read more.

Re: Windows 7 and driver signing Posted: 11 Jan 2013 12:57 AM PST Thanks eried and karlok. I've tried installing the enhanced IDE (solution 3) but it still says that there is a problem with installing the drivers because they are unsigned. I admit I'm a bit reluctant to try 2 because the driver is a built-in Windows ...

Re: 3 axis accelerometer to monitor dryer. Posted: 11 Jan 2013 12:57 AM PST did u look at the readings when u shake it? maybe u can c a characteristic pattern?

Re: Weather sealing a PIR motion sensor ideas? Posted: 11 Jan 2013 12:55 AM PST i m in germany and use the cheapest slime i can find... i just take care that it is good for fish tanks... when it doesnt hurt fishes then it wont hurt me...

Re: [Einsteiger] Nur von Luft und Liebe.. äh Licht Posted: 11 Jan 2013 12:55 AM PST Quote from: uwefed on January 10, 2013, 05:55:08 PM 230V AC schalten ist legal aber wenns man's falsch macht gefährlich für Leib und Gut. Also würdest du mir generell davon abraten, oder lediglich entsprechende Vorsic...

how to use LabVIEW for receive data from serial monitor ? Posted: 11 Jan 2013 12:51 AM PST Can i use 2 Xbees(one with arduino to LabVIEW and one with LM35) and 1 Arduino for temperature monitoring in LabVIEW ? , How to use LabVIEW(LIFA or VISA) for receive data from serial monitor arduino ? I'm newbie for LabVIEW Arduino and Xbee and I'm so...

MOVED: Program the Arduino Ethernet board Posted: 11 Jan 2013 12:45 AM PST This topic has been moved to Networking, Protocols, and Devices. http://arduino.cc/forum/index.php?topic=142090.0

Re: Überlaufprobleme umgehen Posted: 11 Jan 2013 12:44 AM PST Direkte Programmierung => arbeiten mit Registern  ohne das Arduino Framework. Taster sollten nicht unbedingt an Interrupts angeschlossen werden, da die Interrupts dafür viel zu schade sind. (Der Interrupt Kontroller würde sich langweilen ;-))

Re: Controlling and powering a heating element, thermometer, and screen. Posted: 11 Jan 2013 12:43 AM PST Quote from: masterwigglestin on January 10, 2013, 08:10:29 AM Thanks a lot for all the help so far but I am building a cell incubator for growing mammalian cell cultures, not a chicken incubator. Oh, so eggs aren't...

You are subscribed to email updates from Arduino by Davis To stop receiving these emails, you may unsubscribe now.	Email delivery powered by Google
Google Inc., 20 West Kinzie, Chicago IL USA 60610